Lectrosonics DNT16i DANTE INTERFACE, 16 INPUTS

Description Lectrosonics DNT16i DANTE INTERFACE, 16 INPUTS The Lectrosonics DNT16i processor is professionally designed capable of providing inputs into a Dante network from analog and digital signals. Each input is made for providing an extensive signal processing and routing to any one or all of 48 automatic mixers operating at the crosspoints of an internal digital matrix in the processor. The outputs of the matrix are possible to be assigned to a Dante transmit channel and/or routed back to an input to be further mixed that comes with another input or matrix mix. 16 mic/line analog inputs with 48V phantom power and wide range gain control 16 DanteTM digital inputs 32 DanteTM digital outputs Supports both switched and redundant modes in DanteTM operation Pre-mixing signal processing on all 32 inputs (analog and digital) 48 independent automatic mixers with 36 inputs per mixer and channel activity detectors Support for multi-level mixing: mixes can be looped back and used as mixer inputs Extensive signal processing including filters, delay and channel linking for dynamic processing (compressors, limiters) Gain smoothing to prevent transient noise during instantaneous level changes Four test signal generators available for system setup and testing Extensive macro command language Control interfaces via USB, RS-232, Ethernet and programmable logic I/O Rack mount or under table mount Specifications Audio Inputs (Balanced microphone/line level inputs with digitally programmable gain may be configured as unbalanced inputs)Audio Input ChannelsAnalog: 16 mic/line levelDigital: 16 Dante channelsGainAnalog: 0 dB to 56 dB, programmable in 8 dB steps (the analog gain is automatically set by selecting the input gain)Digital (Dante): -70 dB to +20 dBPerformanceImpedance: 8kΩ differential mode, 2kΩ common modeMaximum Analog Input Level: 20 dBuDynamic Range: 102 dBEIN: -127 dBu (20 Hz to 20 kHz, unweighted)THD + Noise: 0.01%A-D Sampling Rate: 48 kHz, fixed Audio Outputs Digital: 32 outputs delivered to the Dante network Dante Interface Provides dual RJ-45 connectors on the rear panel and an Ethernet switch built into the processorSupported Sampling Rate: 48 kHzData Rate LED: 100 Mbps/1 GbpsActivity LED: Blinks when activeModes of OperationSwitched mode using either connectorRedundant mode with primary and secondary networks using both connectors Network Connectivity Dante interface and Ethernet control can be connected to the same network Filters All filters have zero processing delayTone Control Stages: 4 per input channelADFE: 8 per input channel, configurable as static or dynamic Internal Signal Generator Swept SineModes: Single sweep, continuous sweepWaveforms: Sawtooth (up or down), triangleSweep Rate: Linear, logarithmicParameters: Start freq, stop freq, level (dBu), sweep time (sec)White Noise Parameter: Level (dBu)Pink Noise Parameter: Level (dBu)Tone (Sine Wave) Parameters: Level (dBu), frequency Filter Type Low PassButterworth 6, 12, 18, 24 dB/octaveBessel 6, 12, 18, 24 dB/octaveLinkwitz-Riley 12, 24 dB/octaveAdditional Parameters: Frequency (Hz)High PassButterworth 6, 12, 18, 24 dB/octaveBessel 6, 12, 18, 24 dB/octaveLinkwitz-Riley 12, 24 dB/octaveAdditional Parameters: Frequency (Hz)Low ShelvingButterworth 6, 12, 18, 24 dB/octaveBessel 6, 12, 18, 24 dB/octaveAdditional Parameters: Frequency (Hz), boost/cut (dB)High ShelvingButterworth 6, 12, 18, 24 dB/octaveBessel 6, 12, 18, 24 dB/octaveAdditional Parameters: Frequency (Hz), boost/cut (dB)Peaking EQ ParametricParameters: Frequency (Hz), bandwidth (octave), boost/cut (dB) Compressor Soft knee with RMS level detector eliminates need for separate attack and delay settings0.1 ms increments1 second maximumContinuously adjustable ratio Power Requirements 100~240 VAC, 50/60 Hz 20 W maximum consumption Dimensions (WxDxH) 19 x 7.7 x 1.75" (483 x 196 x 44 mm) Weight 5.3 lb (1.7 kg)