Lectrosonics DNT0212 DANTE INTERFACE, 2 IN, 12 OUT

Description Lectrosonics DNT0212 DANTE INTERFACE, 2 IN, 12 OUT The Lectrosonics DNT0212 processor subscribes to channels on a Dante network and is professionally designed capable of delivering them to an internal digital matrix intended for automatic mixing and processing, and to Dante network transmit channels. In addition, two analog line level inputs are made being provided for use along with local sources audio sources such as voice evacuation announcements. The outputs of the matrix are possible to be assigned to a Dante transmit channel, an analog output and/or routed back to an input to be further mixed and processed that comes with another input channel or matrix mix. 32 inputs from DanteTM receive channels 2 analog line level inputs 16 outputs to DanteTM transmit channels 8 line level analog outputs 4 mic/line level analog outputs Supports both switched and redundant modes in DanteTM operation Post-mixing signal processing on all inputs (analog and digital) 48 independent automatic mixers with 38 inputs per mixer and channel activity detectors Support for multi-level mixing: mixes can be looped back and used as mixer inputs Extensive signal processing including filters, delay and channel linking for dynamic processing(compressors, limiters) Gain smoothing to prevent transient noise during instantaneous level changes Four test signal generators available for system setup and testing Extensive macro command language Control interfaces via USB, RS-232, Ethernet and programmable logic I/O Rack mount or under table mount Specifications Audio Inputs (Balanced microphone/line level inputs with digitally programmable gain may be configured as unbalanced inputs)Audio Input ChannelsDigital: 32 Dante channelsAnalog: 2 line level analog (for paging)Gain: -20 dB to +20 dBImpedance: 15kΩ differential, 3.75kΩ commonMaximum Analog Input Level: 20 dBuDynamic Range: 102 dBTHD + Noise: 0.01%A-D Sampling Rate: 48 kHz, fixed Audio Outputs Digital: 16 Dante transmit channelsAnalog: 12 channelsLevel: 0 dBu nominalImpedance: Channels 9~12 include 20 dB and 40 dB attenuators Dante Interface Provides dual RJ-45 connectors on the rear panel and an Ethernet switch built into the processorSupported Sampling Rate: 48 kHzData Rate LED: 100 Mbps/1 GbpsActivity LED: Blinks when activeModes of OperationSwitched mode using either connectorRedundant mode with primary and secondary networks using both connectors Network Connectivity Dante interface and Ethernet control can be connected to the same network Filters All filters have zero processing delayEQ Stages: 4 per input channel Internal Signal Generator Swept SineModes: Single sweep, continuous sweepWaveforms: Sawtooth (up or down), triangleSweep Rate: Linear, logarithmicParameters: Start freq, stop freq, level (dBu), sweep time (sec)White Noise Parameter: Level (dBu)Pink Noise Parameter: Level (dBu)Tone (Sine Wave) Parameters: Level (dBu), frequency Filter Type Low PassButterworth 6, 12, 18, 24 dB/octaveBessel 6, 12, 18, 24 dB/octaveLinkwitz-Riley 12, 24 dB/octaveAdditional Parameters: Frequency (Hz)High PassButterworth 6, 12, 18, 24 dB/octaveBessel 6, 12, 18, 24 dB/octaveLinkwitz-Riley 12, 24 dB/octaveAdditional Parameters: Frequency (Hz)Low ShelvingButterworth 6, 12, 18, 24 dB/octaveBessel 6, 12, 18, 24 dB/octaveAdditional Parameters: Frequency (Hz), boost/cut (dB)High ShelvingButterworth 6, 12, 18, 24 dB/octaveBessel 6, 12, 18, 24 dB/octaveAdditional Parameters: Frequency (Hz), boost/cut (dB)Peaking EQ ParametricParameters: Frequency (Hz), bandwidth (octave), boost/cut (dB) Compressor Soft knee with RMS level detector eliminates need for separate attack and delay settings0.1 ms increments1 second maximumContinuously adjustable ratio Power Requirements 100~240 VAC, 50/60 Hz 20 W maximum consumption Dimensions (WxDxH) 19 x 7.7 x 1.75" (483 x 196 x 44 mm) Weight 5.3 lb (1.7 kg)