Happymodel 1-2S Crux3 3 inch Brushless Toothpick Drone with Frsky SPI/Flysky SPI/DSM2/X SPI/RXSR/TBS Receiver
Happymodel 1-2S Crux3 3 inch Brushless Toothpick Drone with Frsky SPI/Flysky SPI/DSM2/X SPI/RXSR/TBS Receiver Features:41gram 1-2s brushless Toothpick droneNew AIO 4in1 CrazybeeX flight controller CADDX ANT CameraNew 1202.5 brushless motorXT30 connectorRecommend to use 2s 350mah/400mah/450mah/520mah battery（battery not included）Compatible with Insta360 Go Camera You may find the battery,Please click here. Specifications：Brand Name: HappymodelItem Name: Crux3Wheelbase: 115mmSize: 97mmx97mmx35mm(without propellers)Weight: 41g(without battery) Receiver option:Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)Internal SPI DSM2/DSMX version(Compatible with Spektrum or Multiprotocol DSM2/X radio)External Frsky RXSR receiver version(ACCST D16 sbus output)External TBS Crossfire Nano receiver version Introduction:MotorMode: EX1202.5 KV 6400Configuration:9N12PStator Diameter:12mmStator Length:2.5mmShaft Diameter:Φ1.5mmMotor Dimension(Dia.*Len):Φ14mm*14.5mmWeight(g):4.4gNo.of Cells(Lipo):1-2SPropellersGemfan 3018-2Center Thickness:5.5mmProp Diameter:76.5mmCenter Hole diameter:1.5mmFlight controller(Frsky SPI RX version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR(Flysky SPI RX version) CRAZYBEEX FS V2.2 FC Firmware target: CrazybeeF4FS(DSM2/X SPI RX version)CRAZYBEEX DXS V1.0 FC firmware target:CrazybeeF4DXS(External Frsky RXSR version) CRAZYBEEX PNP V2.2 Firmware target:CrazybeeF4DX(External TBS CRSF NANO version) CRAZYBEEX PNP V2.2 Firmware target:CrazybeeF4DXMCU:STM32F411CEU6 (100MHZ, 512K FLASH)Sensor: MPU-6000(SPI connection)Board size: 28.5 * 28.5MMPower supply: 1-2S battery input (DC 2.9V-8.7V)Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 readyBuilt-in Betaflight OSD(SPI Control)Built-in 5.8G VTXBuilt-in SPI Frsky/Flysky receiver or no receiverBuilt-in 5V 1A BECOnboard 4in1 ESCMCU upgraded to EFM8BB21Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds)Support BLHeliSuite programmableFactory firmware: S_H_50_REV16_7.HEXDefault protocol: DSHOT600Onboard Frsky SPI D8 receiver VersionSPI BUS receiver Frsky D8 compatibleCompatible Non EU transmitter D8 modelChannels: 8chFailsafe supportNo ground interference ( Transmitter and receiver 1 m from the ground): 200m~300mOnboard Flysky SPI receiver VersionSPI BUS receiverProtocol: AFHDS and AFHDS-2A SwitchableChannels: 8ch(AFHDS) or 14ch(AFHDS-2A)No ground interference ( Transmitter and receiver 1 m from the ground): 200~300mFailsafe supportOnboard DSM2/X SPI receiver VersionSPI BUS receiver DSM2/DSMX compatibleChannels: Max 12ch Failsafe supportNo ground interference ( Transmitter and receiver 1 m from the ground): 200m~300mRSSI enable(show on the goggles)External Frsky R-XSR receiver versionWeight: 1.5gNumber of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel)Operating Voltage Range: 3.5V~10VOperating Current:70mA@5VFirmware UpgradableCompatibility: FrSky X Series modules and radios in D16 mode Could support Frsky New ACCESS Protocol ( Upgrade firmware)External TBS CRSF Nano receiver versionOriginal TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatibleOnboard 5.8g VTXOutput power: 25mw~200mw switchableFrequency: 40CHInput voltage: 3.3V 5.5VCurrent consumption: 300mA(type)Frequency: 5.8GHz 5bands 40 channelsWith Race band Smartaudio readyCaddx ANT 1200tvl cameraImage Sensor: 1/3" CMOS SensorHorizontal Resolution: 1200 TVLTV System: NTSC or PAL IMAGE: 16:9 or 4:3Synchronization: InternalElectronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000S/N Ratio : >52dB (AGC OFF)Video Output: CVBSLens: 1.8mmMin. Illumination: 0.001Lux@F1.2Auto Gain Control: YESBLC: YESWDR: Global WDRDNR: 3D DNRDimensions: 14*14mm(with bracket to 19*19mm)Wide Power Input: DC 3.7-18VWork Temperature: -20℃~+60℃Weight: 2g (N.W.) Package included:Item Name1*Crux3 Frame and canopyOption1: CrazybeeX FR V2.2 built-in internal Frsky SPI D8/D16 receiverOption2: CrazybeeX FS V2.2 built-in internal Flysky SPI receiverOption3:CrazybeeX DXS V1.0 built-in internal DSM2/DSMX SPI receiverOption4:CrazybeeX PNP V2.2 with External Frsky RXSR receiverOption5:CrazybeeX PNP V2.2 with External TBS crossfire nano receiver4*Happymodel EX1202.5 KV6400 brushless motor1*Gemfan 3018 bi-blade Propellers(4cw+4ccw)1*Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera1*5.8G 25mw~200mw 40ch vtx (Flight controller built-in)1*Screw Driver1*Propeller disassemble tool1*Happymodel Handbag