2001-2018 Ford / Mercury / 3-Button Remote Head Key /164-R8070 / FCC: OUCD6000022

Designed for 2011+ models, but backwards compatible with previous years.  3 Button Ford Remote Head Key fob. 80 Bit NEW STYLE NOTE: Some of our Ford remote head keys require separate programming for the remote portion. Simply perform the standard cycle key 8 times, press button process to program remote head. Description Designed for 2011+ models, but backwards compatible with previous years. Works on the Following Models: Ford Econoline 2004-2013 Ford Edge 2007-2015 Ford Escape 2005-2012 Ford Expedition 2003-2016 Ford Explorer 2001-2015 Ford Explorer ST 2001-2010 Ford F-150 2004-2014 Ford F-250 2004-2016 Ford F-350 2004-2016 Ford F-450 2011-2016 Ford F-550 2011-2016 Ford F-650 2011-2017 Ford F-750 2011-2017 Ford Five Hundred 2007-2011 Ford Flex 2009-2018 Ford Focus 2008-2011 Ford Freestar 2005-2007 Ford Freestyle 2005-2009 Ford Fusion 2006-2012 Ford Mustang 2011 Ford Ranger 2001-2011 Ford Taurus 2008-2009 Ford Taurus X 2008-2009 Ford Windstar 2001-2003 Lincoln MKS 2010 Lincoln MKX 2006-2013 Lincoln MKZ 2006-2013 Lincoln Mark LT 2011-2014 Lincoln Navigator 2014-2017 Mercury Mariner 2005-2010 Mercury Milan 2006-2010 Mercury Montego 2007 Mercury Monterey 2005-2007 Mercury Sable 2008-2010 Buttons: LockUnlockPanic Compatible FCC ID: CWTWB1U793 Compatible IC: 1788A-FWB1U793 OEM Part #(s): 164-R8067, 591256 Replaces: Rotunda 164-R8067Rotunda 164-R8070Rotunda 164-R8073Strattec 5921186 (Ford Mustang)Strattec 5912560 (Ford 3-Button)Strattec 5915217 (Lincoln 3-Button)Strattec 5915218 (Lincoln 4-Button) Frequency: -- Chip: Tex 4D-63 80-Bit Battery: CR2032 Emergency Key: Included Test Blade: H75 Reusable: -- Condition: New AFtermarket   Onboard Programming:  Immobilizer: Yes, w/ 2 original keys Aftermarket - Remote Section On Board Programming Programming Instructions: You Must have Two Master Working Keys (keys that came with the vehicle from factory.) to perform this procedure. If you only have one working key or none at all it must be programmed by a dealer or locksmith! If you do have two working key and one of the keys are copies or clone key. The procedure below won’t work. Your New third (unprogrammed) key must also be cut prior to performing this procedure. 1. Insert an existing (working) key into the ignition cylinder. 2. Turn the ignition cylinder ON (Position 3) and back to OFF (Position 1). Ignition should stay in ON position for at least three seconds but no more than ten seconds. 3. Remove the existing key and WITHIN TEN SECONDS, insert a second working key and turn to ON and then back to OFF. Ignition should stay in ON position for at least three seconds but no more than ten seconds. 4. Remove the second key, insert the New (unprogrammed) key before twenty seconds have elapsed and turn to ON. Leave it in the ON position for at least six seconds and turn back to OFF. 5. If the new key has been successfully programmed it will start the vehicle and operate the remote keyless entry system. The theft indicator light will light up for three seconds to indicate the key was successfully programmed. Remote Programming: Obtain all remote transmitters for this vehicle. It's not necessary to re-program your working remote head keys as those will continue to work. If you are programming additional non-remote head key remotes for your vehicle then they must all be programmed during this procedure. You are able to program up to Four remotes in addition to your remote head keys. Do not depress the brake pedal during procedure. 1.Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (Off is the position where you can remove your key, RUN is the position just shy of starting your car.) 2.Within 20 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 4. 3.Within 20 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 3. for all other remotes. 4.Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.