RPNB Desk Mounted Fingerprint Handgun Safe With Quick Access Drop Down Lid RP311F

RPNB Desk Mounted Fingerprint Handgun Safe With Quick Access Drop Down Lid RP311F Need a quick way to keep your handgun safe and secure? Check out this RPNB fingerprint nightstand gun safe. You can use the smart biometric fingerprint scanner, digital keypad or manual lock keys for access. User-friendly design makes it easy to open even for a single hand. Also it's easy to install and program. Only need a few seconds to mount it under a desk or nightstand with the mounting bracket. For added convenience, mountable from right, left, or top side, depending on desired preference. Features Easily program personal code in seconds Fast-activation drop-down drawer for quick access 500DPI Semiconductor biometric fingerprint Stores up to 50 fingerprint scans Precise fittings are virtually impossible to pry open with hand tools Protective foam-lined interior Multiple mounting options from right, left, or top side Low Battery Alert Support setting to Silence Mode California DOJ Certified Handgun Safe Specifications Item Weight : 7.98 LBSFingerprint Storage : ≤50Password Length : 4-6 DigitsExterior Dimensions : 14.76" x 3.15" x 7.48" (H x W x D)Requirements for Battery : 4 NEW AAA Alkaline Batteries (not included in the box) Package Details Mounting BracketOwner's ManualAnchor Bolts For Mounting (2 set)Backup Keys (2) Warning DO NOT PLACE OR STORE THE BACKUP KEYS INSIDE THE SAFE AT ANY TIME. IF THE BATTERY FAILS, YOU WON'T BE ABLE TO OPEN THE SAFE.DO NOT expose to extreme heat or cold. Battery power may be affected.DO NOT store loaded guns in this unit. Firearms are serious in nature and must be handled with respect.ALWAYS check to make sure the safe is closed and locked when it is not in use. Manual  Desk Mounted Firearm Safety Device Instruction Manual (RP311F) Battery Installation To get started, insert one of your backup keys into the keyhole at the front of the safe. Push key in and turn it counterclockwise to open the safe. Locate the battery compartment door on the inside of the safe directly behind the keypad. Open the battery cover and insert the 4 AAA alkaline batteries(not included) into the battery compartment. Note that pay attention to the “+” and “-”  The “-”end of the batteries go against the spring inside of the compartment. Repeat above steps for battery replacement. Battery Warnings Always insert batteries correctly with regard to polarity (+ and–) as marked on the battery and the product. Exhausted batteries should be immediately removed from product and properly disposed. IMPORTANT: Your RPNB® safe will automatically lock when you fully close the lid. Master Code Programming First time users should change the default code as soon as possible to prevent unauthorized access to your safe, so it should be kept confidential. Enter default code 1-2-3-4 on the keypad to open your safe. With the safe open, press and hold the "PROGRAM" button (3 seconds), all keys(1-4) will flash blue two times with the double beeps. Enter your NEW master code. Press(not hold) the "PROGRAM" button (1 second) and release it to confirm, all keys will flash blue two times with the double beeps. This tone confirms that the password has been reset. If all keys flash red five times with five beeps, it means the safe failed to set the new master code, simply start over with step 2. TIPS: Code Requirements Your code can be a minimum of 4 and a maximum of 6 digits. Two keys cannot be pressed simultaneously. Programming a new code will overwrite your previous code. When you go into confirm password mode, attention please just press(not hold) the "PROGRAM" button "1" second and let it go(Don't press for too long). IMPORTANT: Please keep your new master code in a safe place. Lock-down System If the wrong code or fingerprint is entered five consecutive times, the safe will go into a lock-down mode for five minutes. During this time the buttons will flash red when pressing any buttons and the keypad will be temporarily disabled. The safe can sill be opened using the backup keys override. After five minutes, the safe will automatically resume normal operation. Registering Fingerprints To register your fingerprint, locate the “Program” button. Press and hold the program button(3 seconds) until all keys flash blue two times with the double beeps. Press your finger on the biometric scanner. Removeyour finger when you hear one beep. Then press the same finger on the scanner, remove finger when you hear double beeps and see two blue flashed. Now your fingerprint has been successfully registered. If all keys flash red 5 times with 5 beeps, it means registration has failed and you must repeat the above steps. Note: You cannot register more than 50 fingerprints. If the red light flashes 5 times with 5 beeps when you press the program button, it means the fingerprint storage capacity is full. Registering Fingerprints TIPS: Place your finger on the center of the scanner (this allows the scanner to read where most of the fingerprint detail is located). Adjust your finger slightly between scans for increased accuracy. Excessive moisture, lotions, or dirt will affect your fingerprint and may cause inaccurate sensor reading. If you are experiencing difficulty try different fingers. Each finger is unique and some fingers, such as your thumb, contain more readable information than others. To increase your success rate register the same fingerprint multiple times. Delete the Registered Fingerprint Press and hold the program button. You will see all keys flash blue two times and hear double beeps. Keep holding the program button until you hear another double beeps with two blue flashes, then release it. Now all registered fingerprints are erased. IMPORTANT: When only flash two times with double beeps, do not let go. You must hold the program button until the keys flash twice again with another double beeps, then release it. Low Battery Warning If all keys will light up yellow 6 times with 6 times beeps when opening the safe by electronic way, your battery level is critically low and your safe needs to be replaced the 4 new batteries. Silence Mode Setting To silence the audible sound of the electronics, hold the “1” button for 3 seconds until all the buttons flash blue once together. To unmute the keys, repeat this step. Mounting Your Safe Use proper drilling tools and mounting hardware based on the type of surface you are mounting the safe onto. Supplied screws are intended to be used on wooden surfaces. TIP: Make sure you have enough clearance for the lid to open properly before mounting the safe. Open the safe with the master code or backup keys. Unscrew the thumbscrews located on the inside of the safe. Remove the bracket by sliding it down and off the safe. Use the wall mounting holes on the side or top of the mounting bracket to mark the desired mounting location. Use appropriate mounting hardware to screw the bracket to desired location. Slide the safe onto the bracket mounting hook, fix the safe to the bracket with thumbscrews from inside the safe. Close the safe. The safe can be used now. IMPORTANT: Do not let the safe door face the floor when you mounting the safe with the vertical direction to avoid your property from damage.