2K DTM High Build Primer

Description: Custom Paints Direct to Metal (DTM) Primer. VOC 2.12K DTM Primer-Surfacer with exceptionally high build and direct-to-metal properties. Very soft sanding, wet or dry after short dry times. 2K DTM Primer provides no shrinkage and the maximum in color holdout properties available. Available in 3 colors: grey, white and black which can be blended to make different shades of grey. Suitable for: Car, Motor bike, Caravan, Commercial Vehicle and industrial industry. TYPICAL SUBSTRATES: ▪ OEM primer ▪ GRP / fibreglass ▪ Epoxy primer surfacer ▪ Polyester putties ▪ Existing finishes in good condition ▪ Etch primer Substrates: 2K DTM High Build Primer can be used on the following substrates Metal Galvanized Aluminium OEM primer GRP / Fiberglass Body Filler Polyester putties Mixing: The mixing ratio for 2K DTM High Build Primer: 4 parts 2K DTM High Build Primer 1 part DTM Activator The mixing ratio for 2K DTM Sealer: 4 parts 2K DTM High Build Primer 1 part DTM Activator 1 Part 2K Reducer 2K DTM Primer includes: 2K High Build Primer 1 Quart: 1 Quart High Build Primer. 1/2  Pint Activator. 2K High Build Primer 1 Gallon: 1 Gallon 2K DTM High Build Primer. 1 Quart DTM Activator. SURFACE PREPARATION: Clean and dry the surface. Sand surface with P220—P380 grit abrasive. MIXING: 4 Parts 2k DTM Primer  1 Part Activator Reduction of up to 10-15% with Urethane reducers OPTIONAL MIX 4:1:1 as a SEALER (4 parts primer 1 part Activator, 1 part 2K reducer) POT LIFE 1 Hour @ 70°F (20°C) GUN SET UP: Conventional Siphon Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”) Gravity Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”) HVLP Siphon Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”) Gravity Feed: 1.6 mm – 2.0 mm (0.063” – 0.079”) Air Pressures Conventional Siphon Feed: 35-45 psi at the gun Gravity Feed: 30-40 psi at the gun HVLP 8-10 psi at the gun APPLICATION: Clean surface thoroughly using accepted body shop procedures. Sand per accepted body shop procedures for substrate being used and final clean with solvent wipe. Apply 2-3 medium coats of 2K DTM Primer with 10-15 minutes flash between coats. Do not apply more primer after 1 hour from completion. FLASH TIME/DRY TIMES @ 72ºF / 22.2ºC: Flash/Dry Times (Air Dry): Flash Between Coats: 10-15 minutes Wet Sanding: 1 hour Dry Sanding: 1 hour INFRA RED 15-20 minutes Times can vary depending on the air temperature and air movement.  RE-COAT: Topcoat within 24 hours of sanding. If time exceeds 24 hours, the primed surface must be sanded and cleaned again prior to application of primer or topcoat. SANDING: Dry & D.A.: P400—P600 Wet Sanding: P500—P600 2K DTM Primer Kit includes: 2K High Build Primer 1 Quart Kit: 1 Quart High Build Primer. 1/2  Pint Activator. 1/2 Pint 2K Reducer 2K High Build Primer 1 Gallon Kit: 1 Gallon 2K DTM High Build Primer. 1 Quart DTM Activator. 1 Quart 2K Reducer