F4 Brushed Flight Controller

The classical F4 Brushed Flight Controller comes back with new changes and particular shapes. Build-in CC2500 chip, the default protocol is configured to Frsky D8 out of the factory and can be adjusted to  Frsky D16 FCC, Frsky D16 LBT, or Futaba. Besides, the power cable adopts BT2.0 connector instead of PH2.0, which improves the performance and is compatible with BETAFPV BT2.0 series batteries. Specifications CPU: STM32F411CEU6 Six-Axis: MPU6500 ESC: All FETs are rated at 30A maximum Motor: Support 6x15mm/7x16mm/8x20mm/8.5x20mm etc motors. Recommend BETAFPV 7x16mm Brushed Motors (2CW+2CCW) Size: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting pattern Firmware version: Betaflight BETAFPVF411RX 4.2.11 OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode) Receiver: SPI Frsky D8 (CC2500 chip, adjustable) Power Cable: 55mm, with BT2.0 Connector Weight: 3.68g (with Power Cable) What's the Upgrade Compared with the previous version F4 Brushed Flight Controller V1.2, now the V2.0 version comes with SPI Frsky D8 receiver that can be compatible with Futaba S-FHSS, Frsky D16 FCC, and Frsky D16 LBT protocol. The power cable applies BT2.0 connector instead of PH2.0, which solves the problem of voltage sag, and the discharge can be more efficient, bringing this board a better performance on function for power and responsiveness. What's more, with the compatibility of BETAFPV BT2.0 series batteries, it is convenient to upgrade in the future. Besides, it supports custom RGB lights on the Betaflight configuration, which makes your drone unique from others. Diagram for F4 Brushed Flight Controller Below is the diagram for F4 Brushed Flight Controller. Connection diagram for VTX. Here is the example of M03 25-350mW 5.8G VTX LED status is below. LED Status Description Green Flashing Not connected Green Solid Connected or in bind mode Red Flashing Disarmed Red Solid Motor armed It supports custom RGB lights on the Betaflight configuration. SPI Frsky Receiver With the build-in SPI Receiver CC2500 chip, F4 Brushed FC V2.0 can be compatible with Futaba S-FHSS, Frsky D16 FCC, and D16 LBT protocol. The default protocol is configured to Frsky D8 out of the factory. Pilots could set up the protocol according to their needs in Betaflight Configurator. Configuration Protocol FRSKY_D Frsky D8 FRSKY_X Frsky D16 FCC FRSKY_X_LBT Frsky D16 LBT SFHSS Futaba S-FHSS RECOMMENDED PARTS LIST Battery: BT2.0 300mAh 1S Battery Frame:  65mm Micro Whoop Frame Props: 31mm 3-Blade Motors: BETAFPV 7x16mm Brushed Motors (2CW+2CCW) VTX: M03 25-350mW VTX Recommend drones: Beta65S BNF Micro Whoop Quadcopter FAQ Click here to know SPI Frsky Receiver Binding Manual. Firmware and Cli Dump file for F4 Brushed Flight Controller. Note: Please flash Cli Dump file if you flash firmware from Betaflight official site. Package 1 * F4 Brushed Flight Controller (BT2.0 Connector) 4 * M1.2x4mm screws 4 * M1.4x5mm screws 4 * Anti-vibration rubber dampers